Raman LIDAR Fundamentals

From EG-CLIMET
Jump to: navigation, search

Contents

1 Introduction

In the following a very brief summary of the Raman lidar technique is given. In particular, temperature correction terms have been systemmatically omitted. For a detailed discussion the reader is referred to D. Whiteman, 2003a and D. Whiteman, 2003b and references therein. The rotational Raman technique to measure atmospheric temperature is discussed in more detail in Vaughan et al., 1993.


2 The LIDAR Equation

The lidar (Light Detection and Ranging) technique uses the scattering properties of molecules, aerosols and hydrometeors to derive information on the atmospheric composition or thermodynamic state. A lidar consists of a laser source, generating light pulses at a specific wavelength, of a transceiver to modify the beam diameter and divergence, and of a receiver unit (telescope, spectrometer, acquisition system), to detect the backscattered light as a function of wavelength. In the case of a Rayleigh-Mie lidar system and assuming no multiple scattering, the portion of the emitted power that is backscattered and detected by the receiver unit, P(\lambda_L,r), as a function of range, r, is given by the lidar equation:

 P(\lambda_L,r) = P_0(\lambda_L) O(r) \frac{A}{r^2} C(\lambda_L,r) (\beta_{mol}(\lambda_L,r) + \beta_{aer}(\lambda_L,r)) \exp\left[-2 \int_0^r \alpha(\lambda_L,r') dr' \right] + P_{bg}.

P_0(\lambda_L) is the emitted power at laser wavelength \lambda_L, O(r) is the overlap function, A is the area of the telescope, C(\lambda_L,r) is a system constant accounting for the transmission of the receiver unit, N(r) is the number density of air, \beta_{mol} and \beta_{aer} are the backscatter coefficients of air molecules and aerosols, respectively, \alpha(\lambda_L,r) is the extinction coefficient, and P_{bg} is the background power (straylight or detector noise).

In the case of a Raman lidar system (inelastic scattering) the backscattered power at wavelength \lambda_X, that has been shifted from the laser wavelength due to inelastic Raman scattering by molecular species X, is given by the following expression:

 P(\lambda_X,r) = P_0(\lambda_L) O(r) \frac{A}{r^2} C(\lambda_X,r) \beta(\lambda_L,\lambda_X,r) \exp\left[- \int_0^r \alpha(\lambda_L,r') + \alpha(\lambda_X,r') dr' \right] + P_{bg}.

The molecular backscatter coefficient is given by the number density of the scattering medium, N, and by the backscattering cross section \sigma as follows:

\beta_{mol}(\lambda,r) = N(r)\sigma_{mol}(\lambda).

3 Raman Scattering

For inelastic scattering, the scattering molecule changes its vibrational and/or rotational energy state and hence changes the wavelength of the scattered photon. The change in wavelength depends on the two involved energy levels and is specific for the scattering molecule.

Figure 1: Spectrum of Raman backscatter coefficient for a stimulation wavelength of 355 nm (source: http://lidar.tropos.de/en/research/raman.html)

Since the population of the energy states follows a Boltzman distribution, the Raman backscatter coefficient depends on temperature. This is illustrated in the figure below.

Figure 2: Temperature dependence of the rotational Raman backscatter coefficient (source: http://www.danielaproject.eu/temperature_measure.html)

4 Water Vapor Retrieval

For observations of water vapor, the Raman signal of water vapor at wavelength \lambda_H and of nitrogen at wavelength \lambda_N is measured. Typical wavelength pairs are \lambda_N = 607 nm and \lambda_H = 660 nm for stimulation at 532 nm and \lambda_N = 387 nm and \lambda_H = 407 nm for stimulation at 355 nm. Using the Raman lidar equation presented above, the water vapor mixing ratio q (mass of water vapor to mass of dry air) can be expressed as follows:

q = k_q \frac{O_N(r) \sigma(\lambda_N)}{O_H(r) \sigma(\lambda_H)} \Delta \tau(\lambda_N,\lambda_H,r) \frac{P(\lambda_H,r) - P_{bg,H}}{P(\lambda_N,r) - P_{bg,N}}

where

\Delta\tau(\lambda_N,\lambda_H,r) = \exp\left[-\int_0^r (\alpha(\lambda_H,r') - \alpha(\lambda_N,r)) dr' \right].

k_q is the calibration constant and is determined based on a comparison with an external measurement like a radiosonde.

5 Aerosol Retrieval

A typical parameter that can be derived from a combined elastic-Raman lidar is the backscattering ratio R. It is defined as the ratio between the total backscatter coefficient, \beta_{tot}, and the molecular backscatter coefficient, \beta_{mol}:

 R(\lambda,r) = \frac{\beta_{tot}(\lambda,r)}{\beta_{mol}(\lambda,r)} = \frac{\beta_{mol}(\lambda,r) + \beta_{aer}(\lambda,r)}{\beta_{mol}(\lambda,r)} = 1 + \frac{\beta_{aer}(\lambda,r)}{\beta_{mol}(\lambda,r)}.

The backscattering ratio can be derived from the elastic and the Raman lidar equations and is given by:

R(\lambda_L,r)-1 = k_a C_N(\lambda_L,r) \Delta\tau(\lambda_N,\lambda_L, r) \frac{P(\lambda_L,r) - P_{bg}(\lambda_L)}{P(\lambda_N,r) - P_{bg}(\lambda_N)}.

k_a is a calibration constant and C_N(\lambda_L) accounts for the difference in the backscatter coefficients between wavelength \lambda_N and the laser wavelength \lambda_L. The aerosol backscatter coefficient can be directly derived from the backscattering ratio using a molecular backscatter coefficient profile calculated from a air number density profile obtained from a radiosounding or an atmospheric model.


6 Temperature Retrieval

The temperature dependence of the rotational Raman spectrum is illustrated in Figure 2. Backscatter signals are measured at two different wavelengths in the rotational Raman spectrum and the temperature can be estimated from the ratio of these two signals as follows:

T(r) = \frac{A}{\log \left[ \frac{P(\lambda_{RR1},r)-P_{bg,RR1}}{P(\lambda_{RR2},r)-P_{bg,RR2}} \right] +B}.

A and B are calibration constants, that are derived from intercomparisons external measurements, typically a radiosonde.

Personal tools
Namespaces

Variants
Actions
Navigation
Toolbox
Print/export